如何修理舊叉車的轉向節?
發布時間：2021-11-10 點擊：865
轉向節的主要功能部分山東叉車駕駛叉車時在水平道路,叉車的輪上下波動與水平軸為中心,它可以減少框架的扭力,確保每個叉車輪的負載是偶數,并確保叉車運行穩定。山東叉車轉向節問題如何處理?
the main function of the steering knuckle is that when shandong forklift drives a forklift on the horizontal road, the wheels of the forklift fluctuate with the horizontal axis as the center. it can reduce the torque of the frame, ensure that the load of each forklift wheel is even, and ensure the stable operation of the forklift. how to deal with the steering knuckle problem of shandong forklift?
如何修理舊叉車的轉向節?
how to repair the knuckle of old forklift?
1、二手叉車轉向節頸部出現裂紋時，應及時更換。
1. in case of cracks on the steering knuckle neck of second-hand forklift, it shall be replaced in time.
2. 使用過的叉車轉向節配件e、f軸承的磨損一般不應超過0.05mm。如果大于這個值，可以鍍鉻修復。
2. the wear of bearings e and f of used forklift steering knuckle fittings shall not exceed 0.05mm generally. if it is greater than this value, it can be repaired by chrome plating.
三、轉向節推力軸承平面，應平整，如不平整應修理。
iii. the plane of the thrust bearing of the steering knuckle shall be flat, and if not, it shall be repaired.
4. 二手叉車轉向節配件的螺紋損壞超過2顆牙時，可以修復螺母，也可以堆焊后重新旋回螺紋。
4. when the threads of the steering knuckle parts of the second-hand forklift are damaged by more than 2 teeth, the nuts can be repaired, or the threads can be screwed back after surfacing.
五、二手叉車轉向節的裝配與調整。指節與指節銷軸之間的間隙不得大于0.1mm。
v. assembly and adjustment of used forklift steering knuckle. the clearance between knuckle and knuckle pin shaft shall not be greater than 0.1mm.
6. 轉向節與轉向橋的端部間隙一般為0.05-0.1mm。如果端部間隙過大，可加入調整墊圈。
6. the end clearance between the knuckle and the steering axle is generally 0.05-0.1mm. if the end clearance is too large, the adjusting washer can be added.
7. 二手叉車轉向節軸與轉向橋之間滾針軸承的最大間隙不得大于0.1mm。
7. the maximum clearance of needle bearing between knuckle shaft and steering axle of second-hand forklift shall not be greater than 0.1mm.
8. 轉向節銷孔誤差為0.06mm。當銷孔大于0.1mm時，可用主銷軸將銷孔擴至修復尺寸。
8. the error of knuckle pin hole is 0.06mm. when the pin hole is larger than 0.1mm, the main pin shaft can be used to expand the pin hole to the repair size.
當使用叉車轉向板銷孔磨損時，應不大于0.15mm，否則可按合頁修復大小，用主銷軸。
when using forklift steering plate pin hole wear, should not be more than 0.15mm, otherwise can repair size according to hinge, use main pin shaft.
the main function of the steering knuckle is that when shandong forklift drives a forklift on the horizontal road, the wheels of the forklift fluctuate with the horizontal axis as the center. it can reduce the torque of the frame, ensure that the load of each forklift wheel is even, and ensure the stable operation of the forklift. how to deal with the steering knuckle problem of shandong forklift?
如何修理舊叉車的轉向節?
how to repair the knuckle of old forklift?
1、二手叉車轉向節頸部出現裂紋時，應及時更換。
1. in case of cracks on the steering knuckle neck of second-hand forklift, it shall be replaced in time.
2. 使用過的叉車轉向節配件e、f軸承的磨損一般不應超過0.05mm。如果大于這個值，可以鍍鉻修復。
2. the wear of bearings e and f of used forklift steering knuckle fittings shall not exceed 0.05mm generally. if it is greater than this value, it can be repaired by chrome plating.
三、轉向節推力軸承平面，應平整，如不平整應修理。
iii. the plane of the thrust bearing of the steering knuckle shall be flat, and if not, it shall be repaired.
4. 二手叉車轉向節配件的螺紋損壞超過2顆牙時，可以修復螺母，也可以堆焊后重新旋回螺紋。
4. when the threads of the steering knuckle parts of the second-hand forklift are damaged by more than 2 teeth, the nuts can be repaired, or the threads can be screwed back after surfacing.
五、二手叉車轉向節的裝配與調整。指節與指節銷軸之間的間隙不得大于0.1mm。
v. assembly and adjustment of used forklift steering knuckle. the clearance between knuckle and knuckle pin shaft shall not be greater than 0.1mm.
6. 轉向節與轉向橋的端部間隙一般為0.05-0.1mm。如果端部間隙過大，可加入調整墊圈。
6. the end clearance between the knuckle and the steering axle is generally 0.05-0.1mm. if the end clearance is too large, the adjusting washer can be added.
7. 二手叉車轉向節軸與轉向橋之間滾針軸承的最大間隙不得大于0.1mm。
7. the maximum clearance of needle bearing between knuckle shaft and steering axle of second-hand forklift shall not be greater than 0.1mm.
8. 轉向節銷孔誤差為0.06mm。當銷孔大于0.1mm時，可用主銷軸將銷孔擴至修復尺寸。
8. the error of knuckle pin hole is 0.06mm. when the pin hole is larger than 0.1mm, the main pin shaft can be used to expand the pin hole to the repair size.
當使用叉車轉向板銷孔磨損時，應不大于0.15mm，否則可按合頁修復大小，用主銷軸。
when using forklift steering plate pin hole wear, should not be more than 0.15mm, otherwise can repair size according to hinge, use main pin shaft.